1/18/2024 0 Comments Origami puffer fish![]() symbol, decoration, peace Public Domain origami, butterfly, leaf, paper. My gold fish! It took awhile to blow up but i got it! I made it a little background too. puffer fish, mexico, crafts, dissected, skeleton, animal, traditional. I decided to use a shiny gold but when i took the picture, haha the flash flash blinded me!! :D Origami goldfish my favorite fish "gold fish"" This was a simple design to learn, and fun to do. I think you guys should make a dragon, kangaroo, wolf, macaw stuff like that. i just use an ordinary school paper.! i didn't put eyes on it cuz i can't see any marker.!! nice instructions.!!įrom reader in Trenton "Origami inflatable fish. This is my first try.!! i think it goes well. ![]() I did not have much trouble inflating this fish since I have already made an inflatable balloon. I really liked making the inflatable origami fish and I hope my friends at school get to see this page. Origami inflatable goldfish! My first one I LOVE it!!! Thanks so much for helping me on the way. it inflated better cuz i tucked in the flaps instead of just folding them down." Thanks to Gir for this origami inflatable goldfish. Did yours? Send us your photo and show us! I must admit that my goldfish did not inflate as much as I thought it would. The inspiration to design this model came from the video tut. Origami Inflatable Goldfish Step 12: and there you have it! Your origami inflatable goldfish! Rather Simple Inflatable Origami Puffer Fish modeled after the species Arothron Meleagris. The 1st photo below show the general area and the 2nd photo is a close-up whereby the arrow marks the spot to blow into. 12: Square: Fugu Fish: Sipho Mabona: Czech Origami Convention 2013. Origami Inflatable Goldfish Step 11: Time to inflate the goldfish!! Take a deep breath and blow as hard as you can into the goldfish. Fish: Sipho Mabona: Korea Origami Convention 2015. Origami Inflatable Goldfish Step 10: Now, we'll bring the left flap over to the right. Origami Inflatable Goldfish Step 9: Fold the left flap only over to form a triangle as shown in the photo below. Origami Inflatable Goldfish Step 8: We will now fold the right and left edges over to meet the crease in the center shown by the dash line below. Origami Inflatable Goldfish Step 7: FLIP paper over. Origami Inflatable Goldfish Step 6: OK, we will now fold the top tips down on the dash line as shown below. Origami Inflatable Goldfish Step 5: Now fold the left tip over to the center. Origami Inflatable Goldfish Step 4: Fold the right tip over to the center. Origami Inflatable Goldfish Step 3: Now fold the left side to meet the center crease. Origami Inflatable Goldfish Step 2: Fold the right flap over to meet the center crease. Follow the instructions on our origami waterbomb base page and you should have the following to start with. Origami Inflatable Goldfish Step 1: First, you need to make a waterbomb base. ![]() If I were to fold this again, I would use nicer paper, but it needs to be the same colour both sides as the technique of isolating the fins causes a colour reverse.Made this origami? Comment and Submit your photo using the comment box at the end of this page! In Australia, we have “toadfish” which are more or less the same thing – it too inflates itself to appear more threatening. Fugu I think is considered a delicacy in Japan, raw Fugu will either tickle your tasebuds or kill you due to the inexpertly separated toxic bits. ![]() Like a puffer fish, it inflates and deflates. There is lots to love about this model, including the formation of the eyes and the mouth/tail formation. ![]() Sealing the model closed is a little cheaty (a line of glue seals the belly line), interlocking a raggety edge of partly tessellated paper. The body sort of works itself out – the waterbomb tessellation is not a “flat” tessellation, there is more crenelated paper on one side than the other making the curvature natural. Management of the fins sort of takes care of itself, as they do not really fit with their underlying tessellation bed, they naturally stick up, making modelling of them easy and natural. The progressive tessellation along the body length is curious – each time I thought I could predict and fold more than one level at a time (it is time consuming and anything that speeds up the task would be welcome) I realised I had no idea what I was doing, so undid the mess and went back to one stage at a time. Laying crenelations across these were fiddly in low light, and had I realised they would be angle bisecting squares later then I think I could have been more accurate. That said, with a little large scale and some accurate pre-forming, the laying of the corrugations was fairly straightforward – all based on halves. I have had this model on my “to do” list for ages – I had shied away from it because of what I perceived was a brutal precreasing sequence and impossible collapse: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |